How to Remove a Charcoal Canister in a Grand Cherokee

Removing the charcoal canister in a Grand Cherokee is a straightforward process that can be easily accomplished with the right tools and instructions. By following the steps below, you’ll be able to remove the charcoal canister hassle-free.

Key Takeaways:

  • Raise the vehicle’s rear end using a floor jack and support it on jack stands.
  • Disconnect the EVAP hose from the charcoal canister by releasing the locking teeth on the connector.
  • Disconnect the electrical connector from the NVLD pump by moving the sliding lock to the release position and pressing the release tab.
  • Disconnect the filter hose from the NVLD pump located on the opposite side of the electrical connector.
  • Disengage the canister from the right-side mounting brackets using a screwdriver.
  • Remove the charcoal canister by swinging the right end away from the vehicle and disengaging the mounting slot from the tab at the left mounting bracket.

Tools and Equipment Needed

To remove the charcoal canister from your Grand Cherokee, you will need the following tools and equipment:

ToolsEquipment
ScrewdriverFloor jack
Jack stands

Why these tools and equipment are necessary

A screwdriver is essential for disengaging the mounting brackets and disconnecting the canister. It allows you to release the locking tabs and remove the canister with ease.

A floor jack is necessary to raise the rear end of your Grand Cherokee off the ground, providing access to the canister. It ensures a safe working environment and allows for proper support while removing the canister.

Jack stands are used to securely hold the vehicle in place once it has been raised. They provide an additional level of stability and safety, preventing any unexpected movement while working on the canister.

Remember, safety is paramount when working on your vehicle. Always use the appropriate tools and equipment and exercise caution throughout the removal process.

By gathering these tools and equipment beforehand, you’ll be well-prepared to remove the charcoal canister from your Grand Cherokee without any hassle. Stay tuned for the next section, where we will guide you through raising the vehicle and preparing it for the removal process.

Raising the Vehicle

Before starting the removal process, you need to raise the rear end of your Grand Cherokee and secure it on jack stands. This step will ensure a safe and stable working environment while you are removing the charcoal canister.

To raise the vehicle, follow these steps:

  1. Position a floor jack under the rear end of your Grand Cherokee.
  2. Pump the jack handle or use the provided hydraulic lift mechanism to raise the vehicle.
  3. Once the desired height is achieved, place jack stands under the vehicle’s frame or designated lifting points.
  4. Slowly lower the vehicle onto the jack stands, ensuring that it is securely supported.
  5. Gently shake the vehicle to confirm its stability on the jack stands before proceeding with the removal process.

By following these steps, you will create a safe working environment, allowing you to remove the charcoal canister without any risks or difficulties.

Table: Recommended Tools and Equipment

ToolsEquipment
Socket wrench setFloor jack
ScrewdriverJack stands
PliersProtective gloves
Trim panel removal toolEye protection

Having these tools and equipment handy will make the removal process smoother and more efficient. Remember to wear protective gloves and eye protection to ensure your safety.

Now that you have raised your Grand Cherokee and gathered the necessary tools and equipment, you are ready to proceed with the removal of the charcoal canister.

Disconnecting the EVAP Hose

Begin the removal process by disconnecting the EVAP hose from the charcoal canister. To do this, follow these steps:

  1. Squeeze the inner edges on the release tabs of the EVAP hose’s light-colored connector. This will release the locking teeth from the canister pipe’s raised ridge.
  2. Pull the connector off the pipe to disconnect the hose.

By following these steps, you will ensure a proper disconnection of the EVAP hose without causing any damage to the connector or pipe.

Disconnecting the Electrical Connector

After disconnecting the EVAP hose, the next step is to disconnect the electrical connector from the NVLD pump. Here’s how:

  1. Push the sliding lock on the electrical connector away from the pump and toward the wiring harness. This will move it to the release position.
  2. Press the release tab near the lock and pull the connector off to disconnect it.

Make sure to follow these steps carefully to safely disconnect the electrical connector without any issues.

Disconnecting the Filter Hose

Once the electrical connector is disconnected, it’s time to disconnect the filter hose from the NVLD pump. Follow these steps:

  1. Locate the filter hose on the opposite side of the electrical connector.
  2. Disconnect the filter hose from the NVLD pump by carefully pulling it off.

By properly disconnecting the filter hose, you will ensure all components are ready for the final step of removing the charcoal canister.

Disengaging the Mounting Brackets

Before removing the charcoal canister, it’s important to disengage the mounting brackets. Here’s how:

  1. Use a screwdriver to press the locking tabs at the canister’s right-side mounting brackets.
  2. This will disengage the canister from the brackets, preparing it for removal.

By carefully following these steps and using a screwdriver, you will be able to disengage the mounting brackets without any issues.

Once you have successfully completed these steps, you can proceed to the next section to learn how to remove the charcoal canister from your Grand Cherokee.

Disconnecting the Electrical Connector

After disconnecting the EVAP hose, the next step is to disconnect the electrical connector from the NVLD pump. To do this, you will need to follow these simple steps:

  1. Push the sliding lock on the electrical connector away from the pump and toward the wiring harness. This will move it to the release position.
  2. Press the release tab near the lock, and at the same time, pull the connector off to disconnect it from the NVLD pump.

It’s important to exercise caution and avoid pulling on the wires themselves, as this could cause damage. Take your time and ensure that the connector is fully released before attempting to disconnect it.

Now that you have successfully disconnected the electrical connector, you can move on to the next step in removing the charcoal canister from your Grand Cherokee.

Disconnecting the Filter Hose

To complete the removal process, you need to disconnect the filter hose from the NVLD pump. This step ensures the proper disconnection of all components before removing the charcoal canister from your Grand Cherokee.

To disconnect the filter hose, follow these simple steps:

  1. Locate the filter hose on the opposite side of the electrical connector.
  2. Using your fingers, squeeze the tabs on the connector together to release the locking teeth.
  3. With the tabs squeezed, pull the hose connector off the NVLD pump to disconnect the filter hose.

By following these steps, you will successfully disconnect the filter hose from the NVLD pump, allowing for the proper removal of the charcoal canister. Take care to handle the components gently to avoid any damage during the disconnection process.

StepDescription
Step 1Locate the filter hose on the opposite side of the electrical connector.
Step 2Using your fingers, squeeze the tabs on the connector together to release the locking teeth.
Step 3With the tabs squeezed, pull the hose connector off the NVLD pump to disconnect the filter hose.

Remember, taking the necessary precautions and following the correct procedures will ensure a successful removal of the charcoal canister from your Grand Cherokee. Stay safe and enjoy the satisfaction of completing the task on your own!

Expert Tip:

“When disconnecting the filter hose, be gentle and avoid using excessive force to prevent any potential damage to the components. Take your time and follow the steps carefully for a smooth disconnection process.”

Disengaging the Mounting Brackets

Before removing the canister, it is necessary to disengage it from the right-side mounting brackets. This step ensures a smooth and successful extraction process. To disengage the mounting brackets, you will need a screwdriver to release the canister from its fixed position.

Start by locating the right-side mounting brackets, which are secured to the vehicle’s frame. Position the screwdriver’s tip at the top of the bracket’s locking tab and apply gentle pressure to compress the tab. As you compress the tab, you will feel it disengage from the canister.

Move the screwdriver downward to disengage the second tab on the same bracket. Repeat this process for the remaining brackets until all the tabs are released. Take care to avoid applying excessive force, as this may cause damage to the mounting brackets or the canister itself.

Once all the tabs have been disengaged, the canister will be free from the right-side mounting brackets. This enables you to proceed with the next steps of the removal process. Remember to handle the canister with care to avoid any unnecessary damage.

StepProcedure
1Locate the right-side mounting brackets
2Position the screwdriver at the top of the bracket’s locking tab
3Apply gentle pressure to compress the tab
4Move the screwdriver downward to disengage the second tab
5Repeat the process for all remaining brackets

By following these steps and using the appropriate tools, you can safely disengage the mounting brackets and continue with the removal of the charcoal canister in your Grand Cherokee.

Removing the Charcoal Canister

The last step in removing the charcoal canister from your Grand Cherokee is to completely remove it by disengaging the mounting slot from the left mounting bracket. Here’s a summary of the steps you need to follow:

  1. Raise the vehicle’s rear end using a floor jack and support it on jack stands to create a safe working environment.
  2. Squeeze the inner edges of the release tabs on the light-colored connector of the EVAP hose. This will release the locking teeth from the canister pipe’s raised ridge. Pull the connector off the pipe to disconnect the hose.
  3. Push the sliding lock on the electrical connector of the NVLD pump away from the pump and toward the wiring harness. This will move it to the release position. Press the release tab near the lock and pull the connector off to disconnect the electrical connector.
  4. Disconnect the filter hose from the NVLD pump, which is located on the opposite side of the electrical connector.
  5. Using a screwdriver, press the locking tabs at the canister’s right-side mounting brackets to disengage the canister from the brackets.
  6. Now, swing the canister’s right end out and away from the vehicle. Disengage the mounting slot from the tab at the left mounting bracket to completely remove the canister.

By following these steps, you will be able to successfully remove the charcoal canister from your Grand Cherokee. Remember to exercise caution and follow proper safety procedures throughout the process. If you have any doubts or concerns, it’s always a good idea to consult a professional mechanic for assistance.

Source Links

Similar Posts